Product Overview

SLEME202 is a 5 mm three-layer elastic sheet for water-contact areas: a wear-resistant breathable rubber-plastic blend top layer, an independent foam cushion interlayer, and a high-strength polyester non-woven backing. The top surface is formed with a millimetre-scale three-dimensional anti-slip texture for barefoot safety when wet; the foam interlayer provides high-rebound shock absorption and noticeably softer underfoot comfort than SLEME201; the non-woven skeleton delivers dimensional stability and tear strength. The material is water-resistant throughout, permeable and breathable, highly cushioning, mould-inhibiting and weather resistant.

This technical data sheet is compiled for European and North American water park and public pool safety regimes, referencing EN 13845, DIN 51130, EN 16165, ASTM, EU REACH, RoHS 2.0, ISO 14801 and the ISO 11014 safety data sheet framework. It is intended for long-term immersion, high-frequency barefoot traffic and children's splash areas where cushioning comfort and fall protection are especially important.

1. Product Identification

2. Key Features

2.1 Leading wet slip resistance, meeting European and North American pool safety grades — A dedicated micro-textured anti-slip surface delivers stable dry and wet friction coefficients, certified to DIN 51130 R10 and EN 16165 water-contact slip resistance. No slipping under standing water, suitable for barefoot use by adults and children, eliminating water-contact slip and abrasion hazards.

2.2 Three-layer composite, thickened high-rebound structure for superior cushioning and comfort — A wear-resistant rubber-plastic top layer, an independent foamed cushion interlayer and a non-woven base form a three-layer system in a thickened 5 mm build. Compared with SLEME201, shock absorption on impact is further improved, barefoot walking is soft and comfortable, and impact injury to children from falls is substantially reduced. Especially suited to areas with prolonged barefoot walking and frequent running and jumping by children.

2.3 Water-resistant throughout, breathable and blister-free — The rubber-plastic blend top layer is hydrophobic and non-absorbent, and the three-layer structure is permeable and breathable, rapidly venting moisture from the structural substrate. This prevents water vapour from driving blistering, hollowing and delamination, suitable for long-term alternating wet and dry conditions.

2.4 Non-woven composite reinforced backing — The high-strength polyester non-woven skeleton in the base substantially improves tear, tensile and deformation resistance, and provides a free venting channel for substrate moisture so the sheet does not blister or detach. It also increases bond strength between sheet and substrate.

2.5 Long-term mould, bacteria and algae inhibition — The dense modified rubber-plastic structure does not retain water stains or dirt. In high-humidity conditions it effectively inhibits mould and algae growth, preventing pool floors from blackening, becoming slippery or developing odours — easy to clean with no frequent maintenance.

2.6 Weather and ageing resistance, all-weather service — The wear-resistant rubber-plastic blend resists UV ageing, thermal shock and pool chlorine corrosion. It withstands outdoor sun exposure, low-temperature frost and pool disinfectant immersion without chalking, discolouration or embrittlement over long-term use.

2.7 Environmentally safe and water-contact compliant — Free of heavy metals and harmful substances, compliant with EU REACH and RoHS 2.0, non-toxic, odourless and skin-friendly. Fully satisfies the environmental admission requirements for public children's water-contact facilities.

2.8 Modular sheet installation for flexible working — Individual sheets measure 200 mm × 500 mm, easy to cut for irregular areas with minimal seams. They adapt to curved surfaces, ramps and corners at complex water-contact details, and install quickly in both new-build and renovation projects.

3. Technical Data (EN / DIN / ASTM)

All values are tested on the finished composite sheet as a whole, in line with third-party testing standards for European and North American public water-contact facilities. Slip resistance, water resistance, anti-microbial and weathering indices fully meet overseas pool admission requirements.

4. Application Instructions

4.1 Process sequence — Substrate grinding, repair and pre-treatment → apply OICE-901 primer → trowel-apply OICE-904 adhesive → lay SLEME-202 comfort type elastic sheet → weld seams → sealant treatment at details → cure and hand over.

4.2 Substrate requirements — Substrate strength ≥ 25 MPa, moisture ≤ 9 %, surface sound, flat and dry, free of loose sand, oil and loose debris. Grind sharp protrusions flat. Steel structure substrates require a pre-applied anti-rust primer. Repair and level cracks and holes beforehand.

4.3 Application conditions — Ambient temperature 5–38 °C. Do not install in rain or where the substrate holds standing water.

4.4 Grind the substrate and vacuum to remove defects, bringing it to the required installation condition.

4.5 Apply one coat of dedicated primer to the cleaned, ground substrate. Apply evenly and consistently for a fully sealed film.

4.6 Once the primer has dried and cured for 4–6 hours, trowel-apply OICE-904 adhesive over the full area. Apply evenly with no pooling and no misses.

4.7 After the adhesive has been allowed to flash off for 10–20 minutes, lay the 202 elastic sheet in the pre-planned direction. Roll thoroughly with a stainless steel pressure roller to expel air and compact, ensuring the fibre layer is fully wetted and bonded by the adhesive. Sheets are butt-jointed and seams are sealed by welding.

4.8 Detail reinforcement — Provide transition treatment at internal and external corners, equipment plinths and expansion joints. Dedicated sealant may be used for joint filling and sealing.

4.9 Curing — After laying, allow 48 hours before foot traffic. Full bond strength and water resistance are reached after 7 days. Avoid heavy impact and prolonged standing water during curing.

5. Packaging and Storage

5.1 Packaging — Sheets are stacked and fully sealed in moisture-proof PE film, shipped on pallets. Each pack is supplied with a product certificate and batch test report.

5.2 Storage — Store indoors in a cool, dry environment at 5–30 °C, away from open flames, heat sources and oil. Stack sheets flat; do not stack too high or under heavy load, which can deform the sheet and damage the surface anti-slip texture. Factory-sealed shelf life 12 months.

5.3 Transport — Protect against rain, moisture, compression and impact during transport. Avoid prolonged sun exposure and freezing damage to keep the finished product intact.

6. Safety and Environment

6.1 A Safety Data Sheet compliant with ISO 11014 / GHS is supplied, meeting export audit requirements for European and North American water park and public pool projects.

6.2 Safety characteristics — This solid elastic sheet is not a dangerous chemical and contains no volatile harmful substances. It is skin-friendly and non-toxic, suitable for long-term contact by children. During cutting, keep the site ventilated and wear standard protective equipment.

6.3 Environmental compliance — Free of heavy metals and SVHC substances throughout, compliant with EU REACH, RoHS 2.0 and European and North American material safety standards for public water-contact facilities. Environmentally sound, safe and non-toxic.

6.4 Waste disposal — Construction offcuts must be disposed of in accordance with local environmental regulations. Do not discard at will or pollute water bodies.

7. Warranty and Disclaimer

This product is designed for a service life of not less than 10 years. Projects installed by our company as general contractor or by authorised applicators carry a 3-year warranty; product shelf life is 1 year. All data in this document is derived from laboratory testing and field measurement on domestic and overseas water park and pool projects and represents typical performance values. Actual results depend on substrate condition, pre-treatment, installation workmanship, curing environment and service conditions. Before bulk application or volume procurement, users must carry out on-site sample laying to verify slip resistance, bond strength, water-resistance compatibility and substrate compatibility. The manufacturer reserves the right to optimise and update technical parameters. This document is for technical reference only and does not constitute a legally binding warranty contract.

Brand: SLETU Shui Le Tu / SLEME
Manufacturer: Enjoycool Technology (Hong Kong) Limited
R&D and manufacturing base: Guangzhou, China
Document version: V1.0 ｜ 2026-10-12